No data available.
Please log in to see this content.
You have no subscription access to this content.
No metrics data to plot.
The attempt to load metrics for this article has failed.
The attempt to plot a graph for these metrics has failed.
Normal and torsional spring constants of atomic force microscope cantilevers
1.J. P. Cleveland, S. Manne, D. Bocek, and P. K. Hansma, Rev. Sci. Instrum. 64, 403 (1993).
2.J. E. Sader, J. W. M. Chon, and P. Mulvaney, Rev. Sci. Instrum. 70, 3967 (1999).
3.J. L. Hutter and J. Bechhoefor, Rev. Sci. Instrum. 64, 1868 (1993).
4.C. T. Gibson, G. S. Watson, and S. Myhra, Nanotechnology 7, 259 (1996).
5.T. J. Senden and W. A. Ducker, Langmuir 10, 1003 (1994).
6.D. F. Ogletree, R. W. Carpick, and M. Salmeron, Rev. Sci. Instrum. 67, 3298 (1996).
7.G. Bogdanovic, A. Meurk, and M. W. Rutland, Colloids Surf., B 19, 397 (2000).
8.A. Feiler, P. Attard, and I. Larson, Rev. Sci. Instrum. 71, 2746 (2000).
9.R. G. Cain, S. Biggs, and N. W. Page, J. Colloid Interface Sci. 227, 55 (2000).
10.E. Liu, B. Blanpain, and J. P. Celis, Wear 192, 141 (1996).
11.W. C. Young, Roark’s Formulas for Stress and Strain, 6th ed. (McGraw–Hill, New York, 1989).
12.C. P. Green and J. E. Sader, J. Appl. Phys. 92, 6262 (2002).
13.K. Gieck and R. Gieck, Engineering Formulas (McGraw–Hill, New York, 1997).
14.Using finite element analysis, (Ref. 20) it is found that the distance between the center of the mass and the neutral axis of the cantilever, when the mass is aligned with the major axis of the cantilever, has an insignificant effect on the torsional mode of deformation, i.e., coupling into other modes is negligible.
15.This condition is typically satisfied in practice.
16.J. E. Sader, I. Larson, P. Mulvaney, and L. R. White, Rev. Sci. Instrum. 66, 3789 (1995).
17.J. E. Sader, Rev. Sci. Instrum. 66, 4583 (1995).
18.J. M. Neumeister and W. A. Ducker, Rev. Sci. Instrum. 65, 2527 (1994).
19.J. E. Sader, Rev. Sci. Instrum. 74, 2438 (2003).
20.LUSAS, Finite Element Analysis Ltd., Forge House, 66 High St., Kingston upon Thames, Surrey KT1 1HN, UK.
21.S. Timoshenko, D. H. Young, and W. Weaver, Vibration Problems in Engineering (Wiley, New York, 1974).
22.J. E. Sader, J. Appl. Phys. 84, 64 (1998).
23.A. E. H. Love, A Treatise on the Mathematical Theory of Elasticity (Pergamon, London, 1959).
24.J. E. Sader, in Encyclopedia of Surface and Colloid Science, edited by A. Hubbard (Dekker, New York, 2002), pp. 846–856.
25.Veeco, 1171 Borregas Ave., Sunnyvale, CA 94089.
26.M. Tortonese and M. Kirk, Proc. SPIE 3009, 53 (1997).
27.The signal was collected and digitized using a data acquisition board (Ref. 28). Multiple measurements were taken. These were then windowed together using a Hanning function, fast Fourier transformed, and finally averaged together to obtain the required thermal noise spectra (Ref. 29).
28.National Instruments, 6504 Bridge Point Parkway, Austin, TX 78730-5039. The model used was the AT-MIO-16E-1 DAQ.
29.LabVIEW software, available from National Instruments (see Ref. 28).
30.The functional form of the fit to the power spectra was The fitting parameters are and
31.Digital Instruments, 112 Robin Hill Road, Santa Barbara, CA 93117.
32.To ensure that the spheres were aligned with their center of mass as close to the major axis of the cantilever as possible, we measured the horizontal position of the spheres and only used those results in which the off-axis distance was small
33.Engineering Materials Reference Book, 2nd ed., edited by M. Bauccio (ASM International, Materials Park, OH, 1994).
34.S. Ecke, R. Raiteri, E. Bonaccurso, C. Reiner, H. J. Deiseroth, and H. J. Butt, Rev. Sci. Instrum. 72, 4164 (2001).
Article metrics loading...
Full text loading...
Most read this month
Most cited this month