Volume 84, Issue 11, November 2013
Index of content:
Contrast has traditionally been produced in electron-microscopy of weak phase objects by simply defocusing the objective lens. There now is renewed interest, however, in using devices that apply a uniform quarter-wave phase shift to the scattered electrons relative to the unscattered beam, or that generate in-focus image contrast in some other way. Renewed activity in making an electron-optical equivalent of the familiar “phase-contrast” light microscope is based in part on the improved possibilities that are now available for device microfabrication. There is also a better understanding that it is important to take full advantage of contrast that can be had at low spatial frequency when imaging large, macromolecular objects. In addition, a number of conceptually new phase-plate designs have been proposed, thus increasing the number of options that are available for development. The advantages, disadvantages, and current status of each of these options is now compared and contrasted. Experimental results that are, indeed, superior to what can be accomplished with defocus-based phase contrast have been obtained recently with two different designs of phase-contrast aperture. Nevertheless, extensive work also has shown that fabrication of such devices is inconsistent, and that their working lifetime is short. The main limitation, in fact, appears to be electrostatic charging of any device that is placed into the electron diffraction pattern. The challenge in fabricating phase plates that are practical to use for routine work in electron microscopy thus may be more in the area of materials science than in the area of electron optics.
- Optics; Atoms and Molecules; Spectroscopy; Photon Detectors
84(2013); http://dx.doi.org/10.1063/1.4825352View Description Hide Description
Linear Paul traps (LPT) are used in many experimental studies such as mass spectrometry, atom-ion collisions, and ion-molecule reactions. Mass selective resonant quenching (MSRQ) is implemented in LPT either to identify a charged particle's mass or to remove unwanted ions from a controlled experimental environment. In the latter case, MSRQ can introduce undesired heating to co-trapped ions of different mass, whose secular motion is off resonance with the quenching ac field, which we call off-resonance energy absorption (OREA). We present simulations and experimental evidence that show that the OREA increases exponentially with the number of ions loaded into the trap and with the amplitude of the off-resonance external ac field.
New multiplexed all solid state pulser for high power wide aperture kinetically enhanced copper vapor laser84(2013); http://dx.doi.org/10.1063/1.4829075View Description Hide Description
A novel multiplexed scheme is demonstrated to combine two or more pulsed solid state pulsers of moderate capabilities. Pulse power supply comprising of two solid state pulsers of ∼6 kW rating each in multiplexed mode with common magnetic pulse compression stage was demonstrated and optimized for operating with a wide aperture kinetically enhanced copper vapor laser. Using this new configuration, the multiplexed pulsed power supply was capable of operating efficiently at net repetition-rate of ∼13 kHz, 12 kW (wall plug average power), 18–20 kV discharge voltage and pulse rise-time of ∼80 ns. The laser under multiplexed configuration delivered un-interrupted output power of about ∼80 W with scope of further increase in laser output power in excess of 100 W.
Optical-fiber frequency domain interferometer with nanometer resolution and centimeter measuring range84(2013); http://dx.doi.org/10.1063/1.4829615View Description Hide Description
A new optical-fiber frequency domain interferometer (OFDI) device for accurate measurement of the absolute distance between two stationary objects, with centimeter measuring range and nanometer resolution, has been developed. Its working principle and on-line data processing method were elaborated. The new OFDI instrument was constructed all with currently available commercial communication products. It adopted the wide-spectrum amplified spontaneous emission light as the light source and optical-fiber tip as the test probe. Since this device consists of only fibers or fiber coupled components, it is very compact, convenient to operate, and easy to carry. By measuring the single-step length of a translation stage and the thickness of standard gauge blocks, its ability in implementing nanometer resolution and centimeter measuring range on-line measurements was validated.
84(2013); http://dx.doi.org/10.1063/1.4829656View Description Hide Description
Supercontinuum spatial modulation spectroscopy is a facile tool for conducting single molecule/particle extinction spectroscopy throughout the visible and near infrared (420–1100 nm). The technique's capabilities are benchmarked using individual Au nanoparticles (NPs) as a standard since they are well studied and display a prominent plasmon resonance in the visible. Extinction spectra of individual Au NPs with diameters (d) ranging from d ∼ 8 to 40 nm are resolved with extinction cross sections (σ ext ) of σ ext ∼1 × 10−13–1 ×10−11 cm2. Corresponding signal-to-noise ratios range from ∼30 to ∼1400. The technique's limit of detection is determined to be 4.3 × 10−14 cm2 (4.3 nm2). To showcase supercontinuum spatial modulation spectroscopy's broader applicability, extinction spectra are acquired for other model systems, such as individual single-walled carbon nanotubes (SWCNTs) and CdSe nanowires. We show for the first time extinction spectra of individual (8,3) and (6,5) SWCNTs. For both chiralities, their E11 [(8,3) 1.30 eV (952 nm); (6,5) 1.26 eV (986 nm)] and E22 [(8,3) 1.86 eV (667 nm); (6,5) 2.19 eV (567 nm)] excitonic resonances are seen with corresponding cross sections of σ ext ∼ 10−13 cm2 μm−1.
A multi purpose source chamber at the PLEIADES beamline at SOLEIL for spectroscopic studies of isolated species: Cold molecules, clusters, and nanoparticles84(2013); http://dx.doi.org/10.1063/1.4829718View Description Hide Description
This paper describes the philosophy and design goals regarding the construction of a versatile sample environment: a source capable of producing beams of atoms, molecules, clusters, and nanoparticles in view of studying their interaction with short wavelength (vacuum ultraviolet and x-ray) synchrotron radiation. In the design, specific care has been taken of (a) the use standard components, (b) ensuring modularity, i.e., that swiftly switching between different experimental configurations was possible. To demonstrate the efficiency of the design, proof-of-principle experiments have been conducted by recording x-ray absorption and photoelectron spectra from isolated nanoparticles (SiO2) and free mixed clusters (Ar/Xe). The results from those experiments are showcased and briefly discussed.
84(2013); http://dx.doi.org/10.1063/1.4830415View Description Hide Description
A method using modulated continuous wave (CW) visible laser to measure time-resolved fluorescence spectra of trivalent rare-earth ions has been developed. Electro-optic modulator was used to modulate the CW pumping laser with a rise time of 2 μs. CW Nd3+ lasers were used as examples to present the method. Upconversion dynamic process of Ho3+ was studied utilizing a 532 nm CW laser. Quantum cutting dynamic process from Tb3+ to Yb3+ was analyzed by a 473 nm CW laser. This method can be applied to any CW laser such as He-Ne laser, Ar+ laser, Kr+ laser, Ti:sapphire laser, etc.
Reaction cell for in situ soft x-ray absorption spectroscopy and resonant inelastic x-ray scattering measurements of heterogeneous catalysis up to 1 atm and 250 °C84(2013); http://dx.doi.org/10.1063/1.4829630View Description Hide Description
We present a novel in situ reaction cell for heterogeneous catalysis monitored in situ by x-ray absorption spectroscopy (XAS) and resonant inelastic x-ray scattering (RIXS). The reaction can be carried out at a total pressure up to 1 atm, a regime that has not been accessible to comparable in situ techniques and thus closes the pressure gap to many industrial standard conditions. Two alternate catalyst geometries were tested: (A) a thin film evaporated directly onto an x-ray transparent membrane with a flowing reaction gas mixture behind it or (B) a powder placed behind both the membrane and a gap of flowing reaction gas mixture. To illustrate the working principle and feasibility of our reaction cell setup we have chosen ethylene epoxidation over a silver catalyst as a test case. The evolution of incorporated oxygen species was monitored by total electron/fluorescence yield O K-XAS as well as O K-RIXS, which is a powerful method to separate contributions from inequivalent sites. We find that our method can reliably detect transient species that exist during catalytic reaction conditions that are hardly accessible using other spectroscopic methods.
Depth-resolved confocal micro-Raman spectroscopy for characterizing GaN-based light emitting diode structures84(2013); http://dx.doi.org/10.1063/1.4829627View Description Hide Description
In this work, we demonstrate that depth-resolved confocal micro-Raman spectroscopy can be used to characterize the active layer of GaN-based LEDs. By taking the depth compression effect due to refraction index mismatch into account, the axial profiles of Raman peak intensities from the GaN capping layer toward the sapphire substrate can correctly match the LED structural dimension and allow the identification of unique Raman feature originated from the 0.3 μm thick active layer of the studied LED. The strain variation in different sample depths can also be quantified by measuring the Raman shift of GaN A1(LO) and E2(high) phonon peaks. The capability of identifying the phonon structure of buried LED active layer and depth-resolving the strain distribution of LED structure makes this technique a potential optical and remote tool for in operando investigation of the electronic and structural properties of nitride-based LEDs.
- Particle Sources, Optics and Acceleration; Particle Detectors
84(2013); http://dx.doi.org/10.1063/1.4824484View Description Hide Description
The factors affecting the energetic neutral current, the low energy electron current, and the positive ion current emerging from a four-anode-rods ion source have been studied using argon gas. The neutral and electron current were measured using a simple, new technique. It was found that the energetic neutral current and the electron current depend on the positive ion current and the gas pressure. The ratio of the neutral and electron current to the positive ion current increases by increasing the gas pressure. Also it was found that at a pressure equal to 9 × 10−4 mmHg, the ratio of the neutral to the positive ion current reaches 2.34 while the ratio of the electron current to the positive ion current reaches 1.7.
84(2013); http://dx.doi.org/10.1063/1.4825374View Description Hide Description
Compton side-scattering has been used to simultaneously downshift the energy of keV to MeV energy range photons while attenuating their flux to enable single-shot, spectrally resolved, measurements of high flux X-ray sources to be undertaken. To demonstrate the technique a 1 mm thick pixelated cadmium telluride detector has been used to measure spectra of Compton side-scattered radiation from a Cobalt-60 laboratory source and a high flux, high peak brilliance X-ray source of betatron radiation from a laser-plasma wakefield accelerator.
Precision phase control for the radio frequency system of K500 superconducting cyclotron at Variable Energy Cyclotron Centre, Kolkata84(2013); http://dx.doi.org/10.1063/1.4828670View Description Hide Description
Variable Energy Cyclotron Centre (VECC) has commissioned K500 Superconducting cyclotron (SCC) based on MSU and Texas A&M university cyclotrons. The radio frequency (RF) system of SCC has been commissioned with the stringent requirement of various RF parameters. The three-phase RF system of Superconducting cyclotron has been developed in the frequency range 9–27 MHz with amplitude and phase stability of 100 ppm and ±0.1°, respectively. The phase control system has the option to change the relative phase difference between any two RF cavities and maintain the phase stability within ±0.1° during round-the-clock cyclotron operation. The said precision phase loop consists of both analogue In-phase/Quadrature modulator to achieve faster response and also Direct Digital Synthesis based phase shifter to achieve wide dynamic range as well. This paper discusses detail insights into the various issues of phase control for the K500 SCC at VECC, Kolkata.
The external Q factor of a dual-feed coupling for superconducting radio frequency cavities: Theoretical and experimental studies84(2013); http://dx.doi.org/10.1063/1.4828790View Description Hide Description
We propose a theoretical model based on network analysis to study the external quality factor (Q factor) of dual-feed coupling for superconducting radio-frequency (SRF) cavities. Specifically, we apply our model to the dual-feed 704 MHz half-cell SRF gun for Brookhaven National Laboratory's prototype Energy Recovery Linac (ERL). The calculations show that the external Q factor of this dual-feed system is adjustable from 104 to 109 provided that the adjustment range of a phase shifter covers 0°–360°. With a period of 360°, the external Q factor of the coupling system changes periodically with the phase difference between the two coupling arms. When the RF phase of both coupling arms is adjusted simultaneously in the same direction, the external Q factor of the system also changes periodically, but with a period of 180°.
84(2013); http://dx.doi.org/10.1063/1.4832422View Description Hide Description
There is a lack of real-time continuous beam-diagnostic tools for medical cyclotrons due to high power deposition during proton irradiation. To overcome this limitation, we have developed a profile monitor that is capable of providing continuous feedback about beam shape and current in real time while it is inserted in the beam path. This enables users to optimize the beam profile and observe fluctuations in the beam over time with periodic insertion of the monitor.
- Nuclear Physics, Fusion and Plasmas
84(2013); http://dx.doi.org/10.1063/1.4828671View Description Hide Description
A 2D electron cyclotron emission imaging (ECEI) system has been developed for measurement of electron temperature fluctuations in the HL-2A tokamak. It is comprised of a front-end 24 channel heterodyne imaging array with a tunable RF range spanning 75–110 GHz, and a set of back-end ECEI electronics that together generate 24 × 8 = 192 channel images of the 2nd harmonic X-mode electron cyclotron emission from the HL-2A plasma. The simulated performance of the local oscillator (LO) optics and radio frequency (RF) optics is presented, together with the laboratory characterization results. The Gaussian beams from the LO optics are observed to properly cover the entire detector array. The ECE signals from the plasma are mixed with the LO signal in the array box, then delivered to the electronics system by low-loss microwave cables, and finally to the digitizers. The ECEI system can achieve temporal resolutions of ∼μs, and spatial resolutions of 1 cm (radially) and 2 cm (poloidally).
84(2013); http://dx.doi.org/10.1063/1.4829481View Description Hide Description
A novel fast-ion D-alpha (FIDA) diagnostic that is based on charge exchange spectroscopy has been installed at ASDEX Upgrade. The diagnostic uses a newly developed high-photon-throughput spectrometer together with a low-noise EM-CCD camera that allow measurements with 2 ms exposure time. Absolute intensities are obtained by calibrating the system with an integrating sphere and the wavelength dependence is determined to high accuracy using a neon lamp. Additional perturbative contributions to the spectra, such as -molecular lines, the Stark broadened edge D-alpha emission, and passive FIDA radiation have been identified and can be subtracted or avoided experimentally. The FIDA radiation from fast deuterium ions after charge exchange reactions can therefore be analyzed continuously without superimposed line emissions at large Doppler shifts. Radial information on the fast ions is obtained from radially distributed lines of sight. The investigation of the fast-ion velocity distribution is possible due to three different viewing geometries. The independent viewing geometries access distinct parts of the fast-ion velocity space and make tomographic reconstructions possible.
84(2013); http://dx.doi.org/10.1063/1.4829665View Description Hide Description
A spectrally resolved Motional Stark Effect (MSE) diagnostic has been installed at ASDEX Upgrade. The MSE data have been fitted by a forward model providing access to information about the magnetic field in the plasma interior [R. Reimer, A. Dinklage, J. Geiger et al. , Contrib. Plasma Phys.50, 731–735 (2010)]. The forward model for the beam emission spectra comprises also the fast ion Dα signal [W. W. Heidbrink and G. J. Sadler, Nucl. Fusion34, 535–615 (1994)] and the smearing on the CCD-chip. The calculated magnetic field data as well as the revealed (dia)magnetic effects are consistent with the results from equilibrium reconstruction solver. Measurements of the direction of the magnetic field are affected by unknown and varying polarization effects in the observation.
An initial measurement of a fast neutral spectrum for ion cyclotron range of frequency heated plasma using two-channel compact neutral particle analyzers in KSTAR84(2013); http://dx.doi.org/10.1063/1.4829696View Description Hide Description
The accurate measurement of fast neutral particles from high energy ion tails is very important since it is a measure of ion cyclotron range of frequency (ICRF) or neutral beam (NB) ion heating. In KSTAR, fast neutral measurements have been carried out using a compact neutral particle analyzer based on the silicon photo diode since 2010. As a result, the fast neutral spectrum was observed consistent with the ion temperature, diamagnetic energy, and neutron flux in 2011. However, there was fast neutral count beyond the injected neutral beam energy in NB-only heating. Since it is difficult to expect the count unless the temperature is high enough to diffuse the fast ions beyond the beam energy it was required to identify what it is. During the 2012 campaign, the two-channel diode detectors with and without a particle stopper were used to distinguish fast neutral counts and other counts by a hard X-ray or neutrons. As a result, it was confirmed that the high energy component beyond the beam energy originated from a hard X-ray or neutrons. Finally, it was observed that faster neutrals are generated by ICRF heating and enhanced by electron cyclotron heating compared to NB-only heating.
84(2013); http://dx.doi.org/10.1063/1.4832418View Description Hide Description
A miniaturized multidimensional magnetic probe is developed for application in a low-temperature plasma environment. A very high sensitivity for low-frequency magnetic field fluctuations with constant phase run, a very good signal-to-noise ratio combined with an efficient electrostatic pickup rejection, renders the probe superior compared with any commercial solution. A two-step calibration allows for absolute measurement of amplitude and direction of magnetic field fluctuations. The excellent probe performance is demonstrated by measurements of the parallel current pattern of coherent electrostatic drift wave modes in the VINETA (versatile instrument for studies on nonlinearity, electromagnetism, turbulence, and applications) experiment.
- Microscopy and Imaging
84(2013); http://dx.doi.org/10.1063/1.4827076View Description Hide Description
We describe SPIW (scanning probe image wizard), a new image processing toolbox for SPM (scanning probe microscope) images. SPIW can be used to automate many aspects of SPM data analysis, even for images with surface contamination and step edges present. Specialised routines are available for images with atomic or molecular resolution to improve image visualisation and generate statistical data on surface structure.
Development of an adaptable coherent x-ray diffraction microscope with the emphasis on imaging hydrated specimens84(2013); http://dx.doi.org/10.1063/1.4828656View Description Hide Description
This paper describes the development of a versatile coherent x-ray diffraction microscope capable of imaging biological specimens in solution. The microscope is a flexible platform accommodating various conditions, from low vacuum (10−2 Pa) to helium gas filled ambient pressure. This flexibility greatly expands the application area, from in situ materials science to biology systems in their native state, by significantly relaxing restrictions to the sample environment. The coherent diffraction microscope has been used successfully to image a yeast cell immersed in buffer solution. We believe that the design of this coherent diffraction microscope can be directly adapted to various platforms such as table top soft x-ray laser, synchrotron x-ray sources, and x-ray free electron laser with minor relevant adjustments.